Audix MB5050 50-Inch Long Carbon Fiber Boom with M1250B Microphone, Clutch Assembly and Cable

Audix MicroBoom MB5050 (50" Cardioid) (50" MicroBoom & Cardioid Mic)

The MicroBoom MB5050 gives you the Audix 50" MicroBoom arm with their high-quality MB5050 mini cardioid condenser mic - a great all-in-one package for overhead stage miking of orchestras and choirs, ambient room miking, drum-miking, and more. The boom in the MicroBoom MB5050 package can be used in either a horizontal or a vertical position, while the upper end of the boom holds a mini-XLR connector to securely hold the mic in place. The mic has a built-in low noise preamplifier so no bulky external supply is needed. If you want a clean, professional, and elegant miking solution, you'll find it with the Audix MicroBoom MB5050.The Audix M5050 delivers superb sound. It has a fully integrated preamp and detachable cable, as well as strong shielding from interference. It's a great overhead mic for choir and group vocals, on acoustic instruments, for ambient room miking, symphonic area miking, speech presentations, cymbals, and more.The MicroBoom arm combines with the M1250 condenser microphone to become an ideal solution for discreet, overhead miking. This 50-inch carbon fiber boom attaches to any microphone stand, and it weighs in at only 2.5 ounces. Carbon fiber is one of the most lightweight and durable materials on the planet - which is why it's being used to make parts for race bikes, aerospace crafts, motorcycles, and more. The MicroBoom is certainly discrete, but it's also rugged - it has a mini-XLR connector to securely hold the microphone in place while high-quality Mogami cable is used internally to deliver excellent sound to the bottom of the boom, where a mini-XLR male connector awaits.Audix MicroBoom MB5050 Features at a Glance:MicroBoom StandLess than .3 inches diameter2.5 ounces50" lengthMade of Carbon FiberM1250 Condenser Microphone: Transducer Type: Condenser Frequency Response: 80 Hz - 20 kHz Polar Pattern: Cardioid Output Impedance: 150 ohms Sensitivity at 1k: 7.8 mV/ Pa (-42 dbV +/-1.5 dB) Recommended Load Impedance: > 1000 ohms Signal/Noise Ratio (A-weighted): 73 dB Equivalent Noise Level (A-weighted): 21 dB Maximum SPL @ .5% THD: 150 dB Dynamic Range: 129 dB Power Requirements: 48 ? 52 V Connector: 3 pin mini-XLRm Polarity: Positive pressure on diaphragm produces positive voltage on pin 2 relative to pin 3 Housing / Finish: Brass / paint Weight: .6 oz / 17 grams Length: 1.97 inches / 50 mmThe Audix MicroBoom MB1250 is an all-in-one discreet overhead miking solution!

Audix MB5050 50 Carbon Fiber Boom System

The Audix MicroBoom MB5050 Carbon Fiber Boom System consists of a 50 (1270mm) carbon fiber rod that can be used with any of the condenser microphones in the Audix Micros series. Lightweight and able to attach to any microphone stand, the Audix MicroBoom MB5050 is a problem solver for many hard-to-reach miking applications, including choirs, plays, and orchestras.Use the MicroBoom MB5050 with a choice of capsules in the Audix Micros series, for a broad choice of pickup patterns and frequency responses. Audix employs high-quality shielded cable internally to insure the cleanest audio signal path between the microphone and the bottom of the boom. The boom terminates in a mini-XLR male connector. The MicroBoom MB5050 stand adapter is designed for total control over angle, rotation, and position of the carbon fiber rod. A metal thumbscrew locks the rod firmly in place. The final angle and position of the microphone is controlled by the flexible metal gooseneck just below the microphone. The Audix MicroBoom MB5050 provides an ultra-clean, professional, and elegant appearance on stage along with exceptional performance and portability.   Product Features Lighweight, rigidPortable, easy to positionClean, elegant appearanceExcepti onal sound qualityChoice of capsulesNo external power neededAttaches to any mic standCan be used horizontally or vertically25 shielded mic cable with Mini-XLR female XLR male connectorsMic stand adapter with thumbscrew and wing nut adjustments